Rabbit - controller boards

RS485 / RS232 / RS422 / Ethernet converters, Din-rail switches, Modems / WiFi / Wireless / IP65,Panel PC,embedded controllers / PLC besturingen / Touchscreen

Development-Kit met de RCM5700

Extra laag geprijsde starterkit: de RCM5700DevKit (20-101-1274).

Aktie: € 86,00 (OP=OP)
(excl. €10 euro verzendkosten)

Deze Kit bevat:

Klein board (3 cm x 5 cm x 0.27 cm )
Mini PCI Express form factor
Low cost
Rabbit 5000 microprocessor (RCM5700 MiniCore)
10/100Base-T Ethernet
Mini PCI Express form factor
Incl. Development board met 'prototyping area'
Dynamic C 10 ontwikkel programmatuur en documentatie op CD-ROM
USB kabel voor programmering and debugging
Getting Started manual.

*Algemene eigenschappen:* Datasheet Usermanual
Rabbit RCM5700-MiniCore Specifications:
Microprocessor		Rabbit® 5000 @ 50MHz
EMI Reduction		Spectrum Spreader for reduced EMI (radiated emissions)
Ethernet Port		10/100Base-T
SRAM		128K (on-board Rabbit 5000)
Flash Memory (program)		1 MB
Back up Battery		Connection for user-supplied backup battery (to be used for RTC and SRAM)
General Purpose I/O		Up to 32 parallel digital I/O
Serial Ports		6 CMOS-compatible user-configurable ports
Real Time Clock		Yes
Watchdog/Supervisor		Yes
Timers		10x 8-bit timers 1x 10-bit timer 1x 16-bit timer
Pulse Width Modulators		4 channels synchronized PWM with 10-bit counter 4 channels variable –phase or synchronized PWM with 16-bit counter
Input Capture		2 channels
Quadrature Decoder		2 channels
Power		215 mA @ 3.3 V
Serial Rate		Max. asynchronous rate = CLK/8
Battery-Backup		Connection for user-supplied battery (to support RTC and data SRAM)
Slave interface		Slave-port permits use as master or intelligent peripheral with master controller
Realtime Clock (RTC)		Yes
Timers		Ten 8-bit timers (6 cascadable from the first). One 10-bit timer with 2 match registers and one 16-bit timer with 4 outputs and 8 set/reset registers
Watchdog/Supervisor		Yes
Connector-Headers		One 2x25, 1.27mm pitch IDC signal header and One 2x5, 1.27mm IDC progr. header
Power		3.0 - 3.6VDC, 90mA @ 3.3V (preliminary, pins unloaded)

Development-Kit met de RCM5400W (Wifi)

Extra laag geprijsde starterkit: de RCM5400WDevKit. (20-101-1246)

Aktie: € 211,00 (op=op)

Deze Kit bevat:

Geïntegreerde Wi-Fi/802.11b/g
Tot 39 general-purpose I/O lines.
Low cost
Rabbit 5000 microprocessor (gebaseerd op de RCM5400)
Klein: 1.84” × 2.85” × 0.50” (47 mm × 72 mm × 13 mm)
Incl. Prototyping board
Dynamic C 10 ontwikkel programmatuur en documentatie op CD-ROM
Kabel voor programmering and debugging (RS232)
Getting Started manual.

*Algemene eigenschappen:* Datasheet Usermanual
Rabbit RCM5400W Specifications:
Microprocessor		Rabbit® 5000 @ 73.73 MHz
EMI Reduction		Spectrum Spreader for reduced EMI (radiated emissions)
Wifi		Wi-Fi/802.11b/g
SRAM		512K
Flash Memory (program)		512K
Serial Flash Memory		1MB
Back up Battery		Connection for user-supplied backup battery (to be used for RTC and SRAM)
General Purpose I/O		Up to 39 parallel digital I/O lines
Serial Ports		6 CMOS-compatible user-configurable ports
Real Time Clock		Yes
Watchdog/Supervisor		Yes
Timers		10x 8-bit timers 1x 10-bit timer 1x 16-bit timer
Pulse Width Modulators		4 channels synchronized PWM with 10-bit counter 4 channels variable –phase or synchronized PWM with 16-bit counter
Input Capture		2 channels
Quadrature Decoder		2 channels
Power		3.3 V DC ±5% 625 mA @ 3.3 V while transmitting/receiving 175 mA @ 3.3 V while not transmitting/receiving
Serial Rate		Max. asynchronous rate = CLK/8
Battery-Backup		Connection for user-supplied battery (to support RTC and data SRAM)
Slave interface		Slave-port permits use as master or intelligent peripheral with master controller
Realtime Clock (RTC)		Yes
Operating Temperature		-30°C to +75°C
Timers		Ten 8-bit timers (6 cascadable from the first). One 10-bit timer with 2 match registers and one 16-bit timer with 4 outputs and 8 set/reset registers
Watchdog/Supervisor		Yes
Connector-Headers		One 2x25, 1.27mm pitch IDC signal header and One 2x5, 1.27mm IDC progr. header
Power		3.0 - 3.6VDC, 90mA @ 3.3V (preliminary, pins unloaded)

Development-Kit met de RCM4300

De RCM4300 DevelopmentKit bevat:

RCM4300 RabbitCore Module met 10/100Base-T Ethernet-poort en met 2Mb SerialFlash (voor programma),1Mb execution RAM en 512kb data-RAM geheugen, met 8 kanaals 12-bit ADC, 5 seriële poorten 512Mb miniSD-card
Prototyping Board: op dit board kan de RCM4300 worden aangebracht. Op het prototyping board wordt de spanningverzorging voor de RCM4300 geregeld. Daarnaast heeft u de beschikking over 2 schakelaars, 2 LED’s, een RS232-poort en een gebied met vrije spots om eigen elektronica toe te voegen.
USB-Kabel voor programmeren and debuggen
Dynamic C® ontwikkel software versie 10.21 voor het ontwikkelen en debuggen van uw applicatie tot 1 Megabyte code.
Software-add-on modules (normaal tegen betaling, nu inbegrepen in Kit)

FAT file system: wordt voor de RCM4300 gebruikt voor data-opslag op de miniSD-card
RabbitWeb: wordt gebruikt voor het aanmaken van HTML-webpages die in de RCM4300 kunnen worden geladen
SSL, secure socket layer: wordt gebruikt om beveiligde netwerkverbindingen te maken

“Getting Started” Instructies
Complete documentatie op CD inclusief the Rabbit 4000 reference manual
Rabbit 4000 poster met de pin specificaties
Connectors and accessories

Datasheet Usermanual

Ook nog beschikbaar: DevelopmentKit voor Core met Wifi of ZigBee:

WiFi:

RCM4400W Development Kit
Bestaande uit:

- De Core-module RCM4400W met daarop geïntegreerd de WiFi, 802.11b
- Development board met prototyping area
waarop de RCM4400W kan worden
aangebracht
- Dynamic C versie 10
- Programmeerkabel
- Antenne
- Documentatie op CD

ZigBee:

RCM4510W Development Kit
Bestaande uit:

- De Core-module RCM4510W met daarop geïntegreerd ZigBee
- Development board met prototyping area
waarop de RCM4510W kan worden
aangebracht
- Dynamic C versie 10
- Programmeerkabel
- Documentatie op CD

*Algemene eigenschappen:*
Rabbit RCM4000-series Specifications:
Features	RCM4300 (Order nr:20-101-1138)	RCM4310 (Order nr:20-101-1139)
Microprocessor	Rabbit 4000 @ 58.98 MHz
Pin-compatible	Unit is pin-compatible with the all RCM-Coremodules with 4000 processor.
EMI Reduction	Spectrum Spreader for reduced EMI (radiated emissions)
Ethernet Port	10/100 Base-T, RJ-45, 3 LEDs
SRAM	512K
Shared Code/Data and program execution Fast RAM	1MB	512K
Serial Flash memory (used for program)	2MB	1MB
Flash memory for (data storage)	mini-SD 128MB-1GB (Nand Flash)	mini-SD 128MB-1GB (Nand Flash)
Configurable I/O	28 individually configurable I/O	36 individually configurable I/O
Additional inputs	2 startup-mode, reset in, convert	2 startup-mode, reset in
Additional outputs	status, reset out, analog VREF	status, reset out
Analog Inputs	8 channels single-ended, 11 bit or 4 channels differential, 12 bit 180us conversion time	None
Pulse-Width Modulators	4 PWM registers with 10 bit free running counter and priority interrupts.
Input Capture	2 channel input capture can be used to time input signals from various inputs
Quadrature Decoder	2 channel quadrature decoder accepts inputs from incremental encoder modules
Serial Ports	5 shared high-speed CMOS-compatible serial ports (shared with programming port, A/D converter, mini SD and serial)	6 shared high-speed CMOS-compatible serial ports (shared with programming port, A/D converter, mini SD and serial)
Serial Rate	Max. asynchronous rate = CLK/8
Battery-Backup	Connection for user-supplied battery (to support RTC and data SRAM)
Slave interface	Slave-port permits use as master or intelligent peripheral with master controller
Realtime Clock (RTC)	Yes
Timers	Ten 8-bit timers and one 16-bit timer
Watchdog/Supervisor	Yes
Connector-Headers	One 2x25, 1.27mm pitch IDC signal header.One 2x5, 1.27mm IDC progr. header and one miniSD-card socket
Power	350 mA @ 3.3VDC typical
Operating Temp.	without SD-card : -20°C to +85°C. With SD-card: varies according to card specs.
Humidity	5-95%, non-condensing
Board Size	1.84” × 2.85” × 0.84” (47 mm × 72 mm × 21 mm)

Genoemde prijzen zijn excl. B.T.W.

Neem contact met ons op voor een uitgebreide catalogus en prijslijst.